Crude Heating · Phase Separation · Metering · Module Integration
Crude Oil Heating & Separation Module
LINSON OIL supplies project-configured modules that combine crude heating, phase separation and selected metering/control functions for oilfield production, gathering and treatment facilities. Heating method, two-phase or three-phase separation, equipment arrangement, metering, controls and module boundary are defined from the actual wellstream data, operating conditions, treatment objective and site requirements.
- Feed Basis
- Oil / Gas / Water Data
- Heating
- Project Selected
- Separation
- 2-Phase / 3-Phase
- Inspection
- FAT by Project
Integrated Crude Treatment Module
Heating, separation, piping, instruments and optional metering are coordinated around the approved process basis.
Heating + Separation Process Logic
Condition the wellstream with heat where required, then separate and route each phase.
Heating can be used to improve crude mobility or support the intended separation duty, but the required temperature and heating technology are not universal. Separator type, stage count, internals, metering and export arrangement are confirmed from the project process basis.
-
01 / REVIEW
Review the Wellstream
Confirm oil, gas and water rates, viscosity, water cut, gas-oil ratio, solids/sand, pressure, temperature and expected operating variation.
-
02 / HEAT
Add Heat if Required
Select heater or heat-exchanger duty from the target process condition, available utilities, fluid behavior and downstream separation requirement.
-
03 / SEPARATE
Separate the Required Phases
Configure two-phase or three-phase separation, liquid sections, gas handling, sand considerations and level/interface control to the treatment objective.
-
04 / METER & EXPORT
Measure, Control & Transfer
Coordinate required metering, valves, instruments, shutdown logic and oil/gas/water outlet interfaces within the confirmed module boundary.
Applications
Integrated heating and separation for field production and gathering duties.
The module is configured from the actual fluid and facility duty; it is not presented as one fixed separator or one mandatory heating technology.
Wellsite Production
Modules for wellstream conditioning and phase separation where heating is required by the production or transfer basis.
Gathering Stations
Heating and separation integrated with manifolds, piping, metering and downstream gathering interfaces.
High-Water-Cut / Viscous Crude
Project review for crude where fluid mobility, emulsion behavior or water handling affects the heating and separation scheme.
Modular / Revamp Facilities
Factory-preassembled or upgrade modules arranged around existing tie-ins, utilities, plot, lifting and transport restrictions.
Main Systems & Configuration
Combine only the heating, separation and module functions required by the process.
The final equipment list follows the approved P&ID. Heating equipment, separator orientation/type, metering arrangement, chemical interface and control architecture are project-specific.
Heating Equipment
Water-bath, vacuum phase-change, heat-exchanger or another approved project heating route selected from the duty and utilities.
Separator & Internals
Two-phase or three-phase separator with project-defined inlet distribution, liquid sections, mist elimination and control interfaces.
Piping, Valves & Manifolds
Inlet/outlet piping, bypass, drains, vents, isolation, phase routing and tie-ins coordinated to the approved operating philosophy.
Metering & Instrumentation
Flow, pressure, temperature, level/interface, sampling and phase-metering functions included where required by the project.
Optional Process Interfaces
Chemical injection, sand handling, downstream water treatment or additional conditioning functions are included only where specified.
Controls, Structure & Access
Local/remote controls, alarms, shutdowns, skid structure, platforms, lifting and transport provisions follow the project basis.
Engineering Inputs
Wellstream properties and treatment objectives drive both heater and separator selection.
If the process basis is incomplete, send the available wellstream data, P&ID or existing facility information. The missing heating, separation and module interfaces can then be clarified before quotation.
Fluid & Flow Data
Oil, gas and water rates; water cut; gas-oil ratio; density/viscosity; emulsion behavior; sand/solids; corrosive components where available.
Pressure & Temperature Basis
Normal/min/max operating cases, design conditions, inlet temperature, required process condition and available pressure drop.
Heating & Separation Objective
Reason for heating, available fuel/power/heating medium, required phases, metering needs and downstream oil/gas/water destinations.
Project & Site Interfaces
PFD/P&ID, Data Sheet, Technical Specification, hazardous area, materials/corrosion basis, controls, plot, transport and inspection requirements.
Manufacturing & FAT
Factory integration supports a controlled module build and inspection sequence.
LINSON OIL coordinates applicable vessel/heater fabrication, piping prefabrication, skid assembly, valve/instrument installation and control integration according to the approved project scope. Inspection and FAT follow the project specification and ITP.
Engineering Release
Approved P&ID, equipment Data Sheets, GA, materials, controls and inspection points are coordinated before fabrication.
Fabrication & Assembly
Applicable heater, separator, piping, valves, instruments and structural items are fabricated and integrated to scope.
Inspection & Testing
Material, dimensional, applicable NDT, pressure/leak, instrument, electrical and functional checks are performed as required.
FAT & Records
FAT, customer/EPC/third-party witness support and project quality records are arranged where included in the agreed scope.
Related Equipment
Select the heating and separation blocks around the actual duty.
Water Bath Heater
Indirect oilfield heating where this route matches the project utility and process basis.
View Equipment →Vacuum Phase-Change Heater
Phase-change heating option for crude, gas or water service where selected by the project.
View Equipment →Three-Phase Separator
Oil/gas/water separation where the process requires three independent phase outlets.
View Equipment →Metering & Separation Skid
Integrated separation and phase-metering package where heating is not necessarily part of the scope.
View Equipment →Related Solutions & Projects
Connect the module to field treatment logic and real project evidence.
Solution
Crude Oil Heating, Gathering & Separation
Review heating, gathering, separation and export requirements as one field-process objective.
Solution
Oil, Gas & Water Separation / Metering
Connect separator selection and phase measurement to the wider production process.
Separation Project Reference
He50 Three-Phase Separator Skid
Documented project evidence for modular oil/gas/water separation, individual phase metering and factory-prefabricated skid integration.
Broader Treatment Project
Wushi Oilfield Equipment Project
Broader terminal experience processing water-bearing crude with crude dehydration/stabilization functions. This link is contextual and does not claim the exact heating-separation module configuration.
Heating & Separation RFQ
Send the wellstream data, heating objective and required separation duty.
Share available Process Data, wellstream composition/rates, inlet pressure and temperature, required heating duty, phase-separation objective, PFD/P&ID, Data Sheet and Technical Specification. We will review the equipment route and module boundary before quotation.
Detailed datasheets, drawings and project-specific technical documents are prepared after the operating conditions, scope of supply and commercial basis have been sufficiently clarified.