LINSON OIL · Dongying, China
OILFIELD HEATING SYSTEMS FOR OIL & GAS PROCESSING.
Water bath heaters, vacuum phase-change heaters, explosion-proof electromagnetic heaters and integrated heating skids engineered around process fluid, heating duty, operating pressure, site energy and project requirements.
- Design Basis
- Technologies
- Supply Scope
- Verification
What We Supply
Three heating technologies for different field conditions.
Equipment selection is confirmed after reviewing process data, energy availability, hazardous-area requirements, controls and installation constraints.
Indirect Bath Heating
Water Bath Heater
Indirect heating through an intermediate water bath for crude oil, natural gas and other project-specified process streams.
- ◆ Heat-source configuration confirmed by project
- ◆ Process coil and safety/control scope by project
- ◆ Standalone or packaged supply
Phase-Change Indirect Heating
Vacuum Phase-Change Heater
Indirect heating based on a controlled phase-change working-medium system for project duties involving crude oil, natural gas, water or other approved process media.
- ◆ Heat-source arrangement confirmed by project
- ◆ Phase-change heat-transfer cycle
- ◆ Controls and protection by agreed scope
Electric Heating
Explosion-Proof Electromagnetic Heater / Skid
Electromagnetic induction heating equipment for oilfield pipelines, crude-oil handling and tank-related heating duties where project power conditions support electric heating.
- ◆ Electric electromagnetic heating principle
- ◆ Temperature control and protection functions
- ◆ Single unit or integrated heating skid
Technology Selection
How to select the heating system.
There is no one-size-fits-all heater. LINSON OIL starts with the duty and then confirms the heating technology, materials, controls, safety systems, and integration scope.
Review Required Inputs- 01 / PROCESS MEDIUM
Fluid Characteristics
Crude oil, produced water, gas, condensate, multiphase fluid, viscosity, water cut, corrosive components, and solids.
- 02 / HEATING DUTY
Heat Load & Temperature
Required flow rate, inlet and outlet temperature, operating profile, startup condition, and allowable temperature control range.
- 03 / OPERATING PRESSURE
Pressure & Safety
Design pressure, relief requirements, hazardous-area classification, shutdown philosophy, and applicable project standards.
- 04 / SITE ENERGY
Fuel or Electricity
Availability and quality of fuel gas, diesel, electricity supply, voltage, power capacity, utility limitations, and operating preference.
- 05 / INSTALLATION
Layout & Transport
Indoor or outdoor installation, ambient conditions, lifting limits, transport envelope, maintenance access, and foundation conditions.
- 06 / PROJECT SCOPE
Standalone or Skid
Supply a heater only, or integrate process piping, valves, instruments, electrical, controls, insulation, and structure into one package.
Typical Applications
Heating where production conditions demand control.
From a single custom heater to an integrated process package, the supply scope is adapted to the operating environment and agreed project interfaces.
Crude Oil Heating
Heating of crude-oil streams where temperature control is required for transport, gathering or downstream processing.
Gathering Systems
Heating for oilfield gathering, wellsite facilities, transfer lines and central processing applications according to project duty.
Gas Heating
Gas temperature conditioning where heating is required before metering, treatment or other downstream process steps.
Process Temperature Control
Controlled heating for process duties such as separation support, storage, transfer and fluid handling where required by the process.
Skid Integration
Heater packages can be integrated with piping, valves, instruments, controls and structural skid components according to scope.
Package Integration
The heater can be one part of a wider process package.
Depending on scope, integration can include process piping, valves, instrumentation, electrical systems, controls, structural support, insulation, testing and export preparation.
Explore Crude Oil Heating & Gathering →Engineering Inputs
Start with the data you have.
Complete process information supports a faster technical clarification and more accurate proposal. If some data is not available, our engineering team can identify the key assumptions and open points with you.
SEND WHAT IS AVAILABLE: P&ID, EQUIPMENT DATA SHEET, PROCESS FLOW DIAGRAM, OPERATING DATA, SITE PHOTOS, PLOT PLAN, ELECTRICAL SPECIFICATIONS, OR PREVIOUS EQUIPMENT DRAWINGS.
Flow Rate
Normal, minimum, maximum, and turndown flow conditions.
Temperatures
Inlet, target outlet, ambient, and any temperature-control requirement.
Pressure
Operating, design, inlet, outlet, and allowable pressure-drop information.
Fluid Properties
Composition, density, viscosity, water cut, corrosive media, sand, and solids.
Heat Duty
Required duty if known, heating time, continuous or intermittent operation.
Energy Availability
Fuel gas, diesel, electricity voltage, frequency, and available capacity.
Hazardous Area
Area classification, explosion-protection requirements, and project standards.
Site Conditions
Location, climate, elevation, installation layout, transport, and maintenance access.
Heating System Comparison
A practical comparison before final engineering.
| Selection Factor | Water Bath Heater | Vacuum Phase-Change Heater | Electromagnetic Heater / Skid |
|---|---|---|---|
| Primary Energy / Heat Source | Confirmed from project utility and heater configuration | Confirmed from project utility and phase-change heater configuration | Electrical power supply |
| Heating Approach | Indirect heating through a bath and process coil system | Controlled phase-change indirect heat-transfer arrangement | Electric electromagnetic heating with integrated controls |
| Typical Considerations | Heat-source basis, bath and process-coil arrangement, heating duty, controls and safety requirements | Process stability, thermal control requirement, operating and maintenance philosophy | Electrical capacity, hazardous-area requirement, temperature-control and skid scope |
| Integration Scope | Can include heater body, bath and process coil, heat-source system, piping, valves, instruments and controls according to scope | Can include heater body, phase-change working-medium system, process heat-transfer section, piping, instruments, safety devices and controls according to scope | Can include heater, control cabinet, piping, instruments and skid structure according to scope |
Final selection and specifications are subject to process data, project standards, hazardous-area requirements, and technical clarification. No fixed thermal-efficiency, fuel-saving or energy-saving percentage is assumed for all configurations.
Integrated Delivery
Engineering, manufacturing, inspection, and FAT under one roof.
LINSON OIL supports technical clarification, engineering, manufacturing, inspection, FAT, export delivery and project support according to the agreed supply scope.
Custom Design
Process clarification, equipment selection, data sheets, drawings and multidisciplinary package engineering according to project scope.
Own Factory
Fabrication, machining, assembly, surface treatment, piping installation and skid integration for the agreed equipment scope.
Inspection & Documentation
Material and certificate inspection, welding control, dimensional inspection, NDT, testing and project documentation as applicable.
Ready for Site
Agreed functional checks, FAT, preservation, export packing, documentation and logistics coordination before shipment.
Heating System FAQ
Questions before technology selection.
The correct heater should follow the process duty, site energy, hazardous-area basis and package boundary rather than a single catalog parameter.
How do we choose between water bath, vacuum phase-change and electromagnetic heating?
Do water bath and vacuum phase-change heaters always use the same heat source?
Can LINSON OIL supply a complete heating skid?
What information should we send for a technical proposal?
Request for Quotation
Tell us your heating duty.
Share the operating data available now. Our team will review the heating requirement and contact you for technical clarification, equipment recommendation, and quotation scope.
Technical clarification · Custom manufacturing · FAT support · Export delivery